Some new stuff
  1. Arduino Park Control
  2. Arduino USB2serial programming the bare bone
  3. Arduino Projects Videos added
  4. Arduino Xbee projects
  5. Arduino dB Meter 
  6. Trying to get the IOIO going. 
  7. IOIO is going....bluetooth
  8. Attiny 2313 bluetooth bee RC car
  9. Compass and temperature added
  10. AVR programmer
  11. USB2Serial and Ethernet POE
  12. Arduino LPG Sensor
  13. Program the Arduino Mini 05
  14. Lipo Rider Pro in action
  15. EZ Robot Builder kit arrived 10 Nov 2012
  16. Arduino VA Meter!
  17. 05 Nov 2012 Project Sentry Gun.
  18. Attiny85 PIR Sensor 10 Dec 2012 
  19. 0-30VDC3A and 2-28VDC10A bench PSU's
  20. 19 Dec 2012 Arduino Voltmeter LCD
  21. 29 Dec 2012 Arduino Tachometer&Speedometer LCD
  22. 03 Jan 2013 Arduino AC Phase Control. 
  23. 18 Jan 2013 Arduino Distance Meter
  24. 22 Jan 2013 Arduino Digital Clock and Date
  25. 31 Jan 2013 Arduino Digital Clock and Date 8x2 LCD
  26. Feb 2013 LCD and Backpack
  27. Feb 2013 7 Segment Serial Clock Sparkfun. Distance Sensor with "newping" library
  28. Feb 2013 Lelo Remote
  29. 01/03/2013 Arduino Adafruit 7 Seg Digital Clock with RTC and backpack 
  30. Arduino Frequency Meter 26/03/2013
  31. Another RC  Car controlled by Arduino 06/04/2013
  32. My quadcopter project update 25 April 2013
  33. My Aqua Quad Copter Flying 26 April 2013enlightened
  34. Another monster RC truck;strong one! 11July2013cool
  35. X-Frame Quad Copter 31 July 2013cool
  36. Arduino GSM Sheild added.28/8/2013
  37. 1.8inch TFT screen 13/09/2013cool
  38. 04/11/2014 added PID Soldering Iron Control
  39. Added bluetooth servo control 04/11/2014
  40. ESP8266 first try.16/03/2015
  41. Arduino Uno Quadcopter 19 May 2015
  42. IOT WemosD1 Amp Meter

 

 



 

·        Arduino Uno R3 as ISP target Attiny 2313 successful:

Pins 10,11,12 and 13 reset, miso, mosi and sck respectively with 10 uF capacitor between ground and reset of the UNO and pins respectively to 2313 = 1,17,18 and 19

·        Arduino Uno R3 as ISP Target Attiny 85 successful as above target pins 1,5,6 and 7 with the 10uF cap

·        Arduino Uno R3 as ISP target 328 Bare Bone  successful 1,17,18 and 19 as pins on 328 and cap in place

·        Arduino USB2serial and Sparkfun FTDI Basic target Barebone 328 successful:

Ext reset via 100 nF cap to reset of target.

Rx usbserial connected 3 on Bare bone (Tx)

Tx connected to 2 on bare bone (Rx)

5V and ground connected

·        Arduino USB2serial and Sparkfun Basic to targets 2313 and 85 respectively unsuccessful with Tx and Rx and MISO MOSI with the frustrating error SK500 0x00 after the following:

1.      Correct serial port check

2.      Correct driver installed check

3.      Correct bootloader

4.      Baudrate 9600

5.      Different COM ports not above 9 and above 9

6.      Cable checked

7.      Good contacts checked

8.      0.1 uF cap DTR line done

9.      Different chips check

10.   Attiny not enough memory for bootloader

11.   Damaged bootloader on chip.

12.   Add either 120 R resistor or 10 uF cap between reset and 5V

13.   Libusb-1.0.9 checked

14.   Boards.text checked

15.   Programming text checked

16.   Programmer checked on IDE

17.   Target board checked on IDE

·        May be the following to try:

1.      Different AVR?

2.      Different PC�s

3.      AVR setup

4.      Faulty Pro Mini 328??

 

Back Back to top